XREADGROUP GROUP group consumer [COUNT count] [BLOCK milliseconds] [NOACK] STREAMS key [key ...] ID [ID ...]

The XREADGROUP command is a special version of the XREAD command with support for consumer groups. Probably you will have to understand the XREAD command before reading this page will makes sense.

Moreover, if you are new to streams, we recommend to read our introduction to Redis Streams. Make sure to understand the concept of consumer group in the introduction so that following how this command works will be simpler.

*Consumer groups in 30 seconds

The difference between this command and the vanilla XREAD is that this one supports consumer groups.

Without consumer groups, just using XREAD, all the clients are served with all the entries arriving in a stream. Instead using consumer groups with XREADGROUP, it is possible to create groups of clients that consume different parts of the messages arriving in a given stream. If, for instance, the stream gets the new entries A, B, and C and there are two consumers reading via a consumer group, one client will get, for instance, the messages A and C, and the other the message B, and so forth.

Within a consumer group, a given consumer (that is, just a client consuming messages from the stream), has to identify with an unique consumer name. Which is just a string.

One of the guarantees of consumer groups is that a given consumer can only see the history of messages that were delivered to it, so a message has just a single owner. However there is a special feature called message claiming that allows other consumers to claim messages in case there is a non recoverable failure of some consumer. In order to implement such semantics, consumer groups require explicit acknowledgment of the messages successfully processed by the consumer, via the XACK command. This is needed because the stream will track, for each consumer group, who is processing what message.

This is how to understand if you want to use a consumer group or not:

  1. If you have a stream and multiple clients, and you want all the clients to get all the messages, you do not need a consumer group.
  2. If you have a stream and multiple clients, and you want the stream to be partitioned or sharded across your clients, so that each client will get a sub set of the messages arriving in a stream, you need a consumer group.

*Differences between XREAD and XREADGROUP

From the point of view of the syntax, the commands are almost the same, however XREADGROUP requires a special and mandatory option:

GROUP <group-name> <consumer-name>

The group name is just the name of a consumer group associated to the stream. The group is created using the XGROUP command. The consumer name is the string that is used by the client to identify itself inside the group. The consumer is auto created inside the consumer group the first time it is saw. Different clients should select a different consumer name.

When you read with XREADGROUP, the server will remember that a given message was delivered to you: the message will be stored inside the consumer group in what is called a Pending Entries List (PEL), that is a list of message IDs delivered but not yet acknowledged.

The client will have to acknowledge the message processing using XACK in order for the pending entry to be removed from the PEL. The PEL can be inspected using the XPENDING command.

The NOACK subcommand can be used to avoid adding the message to the PEL in cases where reliability is not a requirement and the occasional message loss is acceptable. This is equivalent to acknowledging the message when it is read.

The ID to specify in the STREAMS option when using XREADGROUP can be one of the following two:

  • The special > ID, which means that the consumer want to receive only messages that were never delivered to any other consumer. It just means, give me new messages.
  • Any other ID, that is, 0 or any other valid ID or incomplete ID (just the millisecond time part), will have the effect of returning entries that are pending for the consumer sending the command with IDs greater than the one provided. So basically if the ID is not >, then the command will just let the client access its pending entries: messages delivered to it, but not yet acknowledged. Note that in this case, both BLOCK and NOACK are ignored.

Like XREAD the XREADGROUP command can be used in a blocking way. There are no differences in this regard.

*What happens when a message is delivered to a consumer?

Two things:

  1. If the message was never delivered to anyone, that is, if we are talking about a new message, then a PEL (Pending Entry List) is created.
  2. If instead the message was already delivered to this consumer, and it is just re-fetching the same message again, then the last delivery counter is updated to the current time, and the number of deliveries is incremented by one. You can access those message properties using the XPENDING command.

*Usage example

Normally you use the command like that in order to get new messages and process them. In pseudo-code:

WHILE true
    entries = XREADGROUP GROUP $GroupName $ConsumerName BLOCK 2000 COUNT 10 STREAMS mystream >
    if entries == nil
        puts "Timeout... try again"
        CONTINUE
    end

    FOREACH entries AS stream_entries
        FOREACH stream_entries as message
            process_message(message.id,message.fields)

            # ACK the message as processed
            XACK mystream $GroupName message.id
        END
    END
END

In this way the example consumer code will fetch only new messages, process them, and acknowledge them via XACK. However the example code above is not complete, because it does not handle recovering after a crash. What will happen if we crash in the middle of processing messages, is that our messages will remain in the pending entries list, so we can access our history by giving XREADGROUP initially an ID of 0, and performing the same loop. Once providing an ID of 0 the reply is an empty set of messages, we know that we processed and acknowledged all the pending messages: we can start to use > as ID, in order to get the new messages and rejoin the consumers that are processing new things.

To see how the command actually replies, please check the XREAD command page.